NOTE:
For the Standard Features shipped in the "Factory Integrated Models",
please see the "Configuration Information - Factory Integrated Models"
section.
Processor One of the following depending on Model
Quad-Core Processors
Intel® Xeon® processor
X3470 (2.93GHz, 95W, 8MB, 1333, HT, Turbo 1/1/4/5) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Xeon® processor
X3460 (2.80GHz, 95W, 8MB, 1333, HT, Turbo 1/1/4/5) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Xeon® processor
X3440 (2.53GHz, 95W, 8MB, 1333, HT, Turbo 1/1/2/3) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Core™ processor
i3-550 (3.20GHz, 73W, 4MB, 1333, HT) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Core™ processor
i3-540 (3.06GHz, 73W, 4MB, 1333, HT) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Core™ processor
i3-530 (2.93GHz, 73W, 4MB, 1333, HT) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Celeron® processor
G1101 (2.26GHz, 73W, 2MB, 1066) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
NOTE: HT indicates
that the processor model supports Intel® Hyper-Threading Technology. NOTE: Turbo indicates the maximum potential frequency increment when
using Intel® Turbo Boost Technology, with 4, 3, 2, and 1 cores active. NOTE: DDR3 speed is the maximum memory speed of the processor. Actual
memory speed may depend on the quantity and type of DIMMs installed.
Embedded NC107i PCI Express
Gigabit Ethernet Server Adapter
Expansion Slots #
Technology
Bus Width***
Connector Width
Bus Number*
Device Number**
Form Factor
Notes
1
PCIe
X1
X4
16
0
Full height, half length slot
Gen.1, NHP
2
PCI
32 bit
N/A
48
0
Full height & Full-length slot
33MHz/3.3V, NHP
3
PCIe
X4
X8
32
0
Full height & Full-length slot
Gen.1, NHP
4
PCIe
X16
X16
1
0
Full height & Full-length slot
Gen.2, NHP
*Default
bus assignment (in decimal). Inserting cards with PCI bridges may alter
the actual bus assignment number.
** Slots are enumerated differently based on OS. MS OS's enumerate from
lowest to highest Device ID by bus (starting with the lowest bus).
*** Indicates the number of physical electrical lanes running to a PCI-e
connector.
NOTE: For more information on HP's Certified and Supported ProLiant
Servers for OS and Virtualization Software and latest listing of software
drivers available for your server, please visit our Support Matrix at:
http://www.hp.com/go/supportos
and our driver download page http://www.hp.com/support/ML110G6
Graphics
64MB shared supporting all display
resolutions up to 1600 x 1200 16bpp @ 75Hz NOTE: 8MB is dedicated to video memory.
Form Factor
Micro ATX Tower (4U) NOTE: Rack mounting available via
HP Tower to Rack Conversion Tray, Universal Kit. Please see the options
section in this QuickSpecs.
Embedded Manageability
HP LO100i Advanced
HP LO100i Lights-Out 100 with Optional LO100i Advanced Licenses for Virtual
KVM and Virtual Media.
Features:
Embedded IPMI standard reporting
System event log access
Remote Serial console (serial redirection)
Browser, Telnet access
SMASH-CLP compliant
DCMI 1.0 compliant
IPMI 2.0 compliant
Secure Socket Layer Encryption
Secure Shell Encryption
Virtual media (Floppy, CD, DVD, ISO image, USB 2.0) with Advanced
License
Virtual KVM with Advanced License
NOTE: For more information, please refer
to the QuickSpecs for the LO100i found at: www.hp.com/go/lo100
Core Infrastructure Management
HP ProLiant ML110 G6 Easy Set-up CD
The HP ProLiant Easy Set-up CD optimizes single-server setup, providing
a simple way to deploy reliable and consistent server configurations.
The HP ProLiant 100 Series Easy Set-up CD ships standard with the ML110
G6.
It offers essential single-server deployment tools for HP ProLiant 100
series servers that simplify HP entry server setup, providing a repeatable
way to deploy reliable and consistent single-server configurations. The
HP ProLiant Easy Set-up CD assists with the OS installation process by
preparing the system for installing "off-the-shelf" versions
of Windows operating system software and automatically integrating optimized
HP ProLiant server software drivers and utilities. Users enjoy the following
benefits:
An easy-to-use, intuitive graphical interface that prepares your system
for the OS installation process.
Integration of key server software drivers with assisted installation.
Dependency and validity checks to ensure that all supported ProLiant
software can be installed.
HP Integrated Lights-Out 100i
with optional LO100i Advanced Licenses for Virtual KVM and Virtual Media
Embedded Lights Out 100 IPMI
2.0 standard reporting
Standard HP ProLiant ML110 G6
Easy Set-Up CD
Array Configuration Utility
(ACU)
Array Diagnostics Utility (ADU)
HP Insight Diagnostics
HP Insight Management Agents
and Insight Management Providers for Systems Insight Manager (SIM) Integration
Security
Power-on password
Setup password
Secure Sockets Layer (SSL)
Secure Shell (SSH)
Warranty
This product is covered by a
global limited warranty and supported by HP Services and a worldwide network
of HP Authorized Channel Partners. Hardware diagnostic support and repair
are available for one year from date of purchase. Support for software and
initial setup is available for 90 days from date of purchase. Enhancements
to warranty services are available through HP Care Pack services or customized
service agreements. Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details. NOTE: Server Warranty includes 1
year parts, 1 year labor, 1-year on-site support with next business day
response. (3-1-1 warranty offered in Brazil only). Warranty repairs may
be accomplished through the use of Customer Self Repair (CSR) parts. These
parts fall into two categories: 1) Mandatory CSR parts are designed for
easy replacement. A travel and labor charge will result when customers decline
to replace a Mandatory CSR part; 2) Optional CSR parts are also designed
for easy replacement but may involve added complexity. Customers may choose
to have HP replace Optional CSR parts at no charge. Additional information
regarding worldwide limited warranty and technical support is available
at: http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
HP Factory Express offers configuration, customization, integration and
deployment services for HP servers and/or storage products. Customers
can choose how their factory solutions are built, tested, integrated,
shipped and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as individual
factory services, such as image loading, asset tagging and custom packaging
HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades,
HP BladeSystem, HP 9000 servers, as well as, the MSAxxxx, VA7xxx, EVA,
XP, rackable tape libraries and configurable network switches.
For more information on Factory Express services for your specific server
model please contact your sales representative or go to: http://www.hp.com/go/factory-express
HP Enterprise Configurator
The HP eConfigure Enterprise Configurator now provides factory default
racking for our HP hardware portfolio. This approach is aligned with our
strategic direction to meet the needs and expectations of our valued customers.
If you require "custom" rack configuration, please contact HP's
Customer Business Center or an Authorized Partner for assistance. http://www.hp.com/products/configurator.
For increased uptime, productivity and ROI - HP Care Pack packaged
services for Servers
These days, you need to get the most out of your server investment - you
can't afford not to. When you buy HP server products and solutions, it's
also a good time to think about what levels of service and support you
may need. To help take the worry out of deploying, designing, maintaining,
and managing your environment, we've designed a portfolio of service options
that are as: flexible, reliable and scalable as your server. Unlike server-only
vendors, we take a holistic approach to your entire environment, bridging
storage, servers, blades, software and network infrastructures with our
HP Care Pack packaged services for Servers.
Protect your business beyond the warranty
When it comes to robustness and reliability, standard warranties on today's
computing equipment have matured just as the technologies have matured.
Good news on some fronts - but also a source of potential problems and
subsequent consequences that come from depending on standard warranties
alone. Standard warranty protects against product defects and some causes
of downtime - but not the business. By using a standard approach to warranty
uplifts, such as HP Care Pack Services, you can reduce downtime risks
and be more certain of operational consistency for both mission-critical
and standard business computing. Simply put, HP Care Pack Services normalize
the warranty of combined products - helping you proactively guard against
unplanned downtime.
Extending warranties with HP Care Pack Services
For cost-effective upgrading or extending your standard warranty, HP Care
Pack Services offer a suite of standard reactive hardware and software
support services that are sold separately, or combined as with our Support
Plus and Support Plus 24 services. The portfolio also provides a combination
of proactive and reactive services, such as Proactive 24 Service and Critical
Service. In addition, with HP Proactive Select we offer an innovative
approach to service delivery that gives you the flexibility to acquire
the specific proactive services you need today, then add services as your
needs evolve. HP Proactive Select offers a broad set of technical or per-event
type service options - including server, storage, and network, SAN device,
and software, environment, installation and education services. Services
that you can mix and match depending on your specific requirements, from
preliminary planning and equipment delivery to installation, configuration,
integration, and testing, through every level of ongoing support. Our
HP Care Pack packaged services for Servers assures help when you need
it most. And for many products, post-warranty HP Care Pack Services are
available when your original warranty has expired.
HP Server Services: Offering reliability, flexibility and value -
just like your storage
HP Server Services offers a full spectrum of customer care, from technology
support to complex migrations to complete completely managed services.
HP Factory Express provides customization, integration and deployment
services for turnkey solutions. HP Education offers flexible, comprehensive
training on server networking and server software to help your IT staff
get the most out of your investments. And HP Financial solutions extend
innovative financing and asset management programs to cost-effective buy,
manage and eventually retire your older equipment.
NOTE: Care Pack Services availability
may vary by product and country.
Recommended HP
Care Pack Services for optimal satisfaction with your HP product
Recommended Services
3-Year HP Hardware Support Onsite Service, 4-hour response, 13x5
Delivering increased equipment availability and productivity with rapid-response
onsite and remote support for your HP hardware, as well as selected multivendor
equipment, this flexible HP Care Pack Service covers desktops, workstations,
servers, storage systems, network equipment, and printing.
Choose 4-Hour Same Business Day Hardware Support when you need to:
Extend your hardware warranty coverage with prompt service for key
systems and devices
Obtain easy-to-buy, easy-to-use onsite services
Improve hardware performance and uptime
Increase the return on your HP and multivendor hardware investments
Enjoy consistent service coverage across geographically dispersed
sites
3-Year HP Hardware Support Onsite Service, Next-day response (9x5)
HP ProLiant services: Our integrated service portfolio covers the
entire solution lifecycle for x86 server environments - from installation
and support through the design, deployment, and management of complex
IT environments - so that you can confidently address any IT and business
need.
HP Hardware Support Onsite Service provides high-quality remote assistance
and onsite support for your covered hardware, helping you to improve product
time.
HP Installation Service provides for the basic installation of HP branded
servers, workstations, desktop systems, notebook PCs, thin clients, storage
devices, printers, networking, and software products. The Installation
Service is part of a suite of HP deployment services that are designed
to give you the peace of mind that comes from knowing your HP and HP-supported
products have been installed by an HP specialist in accordance with the
manufacturer's product documentation.
Expedited installation, with all service prerequisites met before
the installation is performed
Installation in accordance with manufacturer's specifications, enhancing
the supportability of your HP-installed hardware and software
Service delivery at a mutually scheduled time
Allows your IT resources to stay focused on their core tasks and priorities
Availability of an HP service specialist to answer questions during
the onsite delivery of this service
3-Year HP Hardware Support Onsite Call-to-Repair (CTR) Service - 24-hour
CTR
As an alternative to our recommended support level, for customers
who need committed call-to-repair for server hardware.
HP Hardware Support Onsite 24x7 24-Hour Call-to-Repair Service provides
your IT manager access to a team of support specialists. They will quickly
begin troubleshooting the system to help return the hardware to operating
condition within a maximum of 24 hours from the initial service request.
HP is committed to repairing your hardware within a maximum of six hours.
The benefits include:
Improved system uptime
Predictable repair times
More effective IT resource planning
Consistent level of hardware support across your multi-technology
systems
3-Year HP Hardware Support Onsite Call-to-Repair (CTR) Service - 6-hour
CTR
As an alternative to our recommended support level, for customers who
need committed call-to-repair for server hardware.
HP Hardware Support Onsite 24x7 6-Hour Call-to-Repair Service provides
your IT manager access to a team of support specialists. They will quickly
begin troubleshooting the system to help return the hardware to operating
condition within a maximum of six hours from the initial service request.
HP is committed to repairing your hardware within a maximum of six hours.
The benefits include:
Improved system uptime
Predictable repair times
More effective IT resource planning
Consistent level of hardware support across your multi-technology
systems
HP eSupport is a portfolio of technology-based services that assist you
with managing your business environment - from the desktop to the data
center.
Support Portal
The HP support portal provides one-stop access to the information, tools
and services you need to manage the daily operations of your IT environment.
Features include:
Access to self-solve tools (including search technical knowledge base)
Efficient logging and tracking of support cases
Collaboration with other business and IT professionals
Download of patches and drivers
Access to diagnostic tools
Proactive notification of relevant information
Access to certain features of the support portal requires an HP service
agreement. To access the support portal, visit: http://www.hp.com/support
HP Insight Remote Support software delivers secure remote support for
your HP Servers and Storage, 24 X 7, so you can spend less time solving
problems and more time focused on your business. You can have your systems
remotely monitored for hardware failure using secure technology that's
been proven at thousands of companies around the world. In many cases,
you can avoid problems before they occur.
Customer Technical Training
HP Services continues to be recognized for service and support excellence
by customers, partners, industry organizations and publications around
the world. Recent honors and award reflect our services team's dedications,
technical expertise, professionalism and uncompromising commitment to
customer satisfaction. For a list of all our awards, please visit: http://h20219.www2.hp.com/services/cache/433028-0-0-225-121.htm
HP Services Awards
HP Services continues to be recognized for service and support excellence
by customers, partners, industry organizations and publications around
the world. Recent honors and award reflect our services team's dedications,
technical expertise, professionalism and uncompromising commitment to
customer satisfaction. For a list of all our awards, please visit: http://h20219.www2.hp.com/services/cache/433028-0-0-225-121.htm
SATA Models NOTE: For the Standard Features shipped
in the "Factory Integrated Models", please see the "Configuration
Information - Factory Integrated Models" section. NOTE: Pre-configured models ship with the configurations below. Options
can be selected from the Core or Additional options section of this QuickSpecs.
NOTE: HP does not allow factory integration of options into pre-configured
models. Any additional options purchased will be shipped separately. NOTE: If you desire a custom configuration please see "Configuration
Information - Factory Integrated Models" section of this QuickSpecs. NOTE: HP NHP Internal SAS/SATA 4 port cable kit (487734-B21) is required
when Smart Array Controller is ordered with a BTO configuration NOTE: For general information about HP Smart Array B110i SATA RAID
Controller, please visit: http://h18004.www1.hp.com/products/servers/proliantstorage/arraycontrollers/smartarrayb110i/index.html
NOTE:
For the Standard Features shipped in the "Factory Integrated Models",
please see the "Configuration Information - Factory Integrated Models"
section. NOTE: This section lists some of the steps required to configure
a Factory Integrated Model. To ensure only valid configurations are ordered,
HP recommends the use of an HP approved configurator. Contact your local
sales representative for information on configurable product offerings and
requirements. NOTE: Configure-to-order (CTO) servers must start with a CTO Chassis. NOTE: FIO indicates that this option is only available as a factory
installable option.
Step 1: Base Configuration
HP Models
HP ProLiant ML110 G6 Configure-to-order
Server
510078-B21
Factory Integrated Models ship
with:
Embedded NC107i PCI Express Gigabit
Ethernet Server Adapter
Integrated HP ProLiant 100 G6
Lights Out 100i Remote Management
NOTE: All DDR3
memory option kits consist of one DIMM per kit. For detailed memory configuration
rules and guidelines, please use the Online DDR3 Memory Configuration Tool
at: www.hp.com/go/ddr3memory-configurator.
HP Optical Drives
HP Half-Height SATA DVD-ROM Optical
Drive
447326-B21
HP Half-Height SATA DVD-RW Optical
Drive
447328-B21
HP Hard Drives
SATA Non-Hot Plug LFF (3.5-inch)
Midline (MDL) Drives
HP 2TB 3G SATA 7.2K rpm LFF (3.5-inch)
Non-hot Plug Midline 1yr Warranty Hard Drive
SAS Non-Hot Plug LFF (3.5-inch)
Enterprise (ENT) Drives NOTE: Support for SAS non-hot plug
drives requires HP SAS/Smart Array Controller. See Step 3 below.
HP 600GB 6G SAS 15K rpm LFF (3.5-inch)
Non-hot Plug Dual Port Enterprise 3yr Warranty Hard Drive
HP 300GB 6G SAS 15K rpm LFF (3.5-inch)
Non-hot Plug Dual Port Enterprise 3yr Warranty Hard Drive
516824-B21
HP Storage Controllers
SAS Controller NOTE: Support for SAS hard drives/tape
drive requires selection of a SAS controller. NOTE: Support for hardware RAID requires selection of a SAS controller.
Smart Array P212 Controller
HP Smart Array P212/256 1-ports
Int/1-ports Ext PCIe x8 FIO SAS Controller
NOTE: Some options
may not be integrated at the factory. To ensure only valid configurations
are ordered, HP recommends the use of an HP approved configurator. Contact
your local sales representative for additional information.
HP S-BUY 1GB (1x1GB) Single Rank
x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9 Memory Kit
500668-S21
NOTE: All DDR3
memory option kits consist of one DIMM per kit. For detailed memory configuration
rules and guidelines, please use the Online DDR3 Memory Configuration Tool
at: www.hp.com/go/ddr3memory-configurator.
HP Optical Drives
HP Half-Height SATA DVD-ROM Optical
Drive
447326-B21
HP Half-Height SATA DVD-RW Optical
Drive
447328-B21
ML110 G6 Hard Drives
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, and firmware)
should operate at the same data transfer rate or the system bandwidth will
be negotiated down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
SATA Non-Hot Plug LFF (3.5-inch)
Midline (MDL) Drives
HP 2TB 3G SATA 7.2K rpm LFF (3.5-inch)
Non-hot Plug Midline 1yr Warranty Hard Drive
NOTE:
Some options may not be integrated at the factory. To ensure only valid
configurations are ordered, HP recommends the use of an HP approved configurator.
Contact your local sales representative for additional information.
HP Entry-Level Server
Management
HP Lights-Out 100i (LO100i) Advanced
including 1yr 24x7 Support Single Server License
530521-B21
NOTE: For additional
License Kits please see the Lights-Out 100i QuickSpecs at: www.hp.com/go/lo100.
HP Security (TPM)
HP Trusted Platform Module Option
488069-B21
NOTE: The TPM
(Trusted Platform Module) is a microcontroller chip that can securely store
artifacts used to authenticate the server platform. These artifacts can
include passwords, certificates and encryption keys. Windows® BitLocker™
Drive Encryption (BitLocker) is a data protection feature available in Windows
Server® 2008. BitLocker leverages the enhanced security capabilities
of a Trusted Platform Module (TPM) version 1.2. The TPM works with BitLocker
to help protect user data and to ensure that a server running Windows Server
2008 has not been tampered with while the system was offline. NOTE: For more information about TPM, please visit: www.hp.com/go/TPM NOTE: ProLiant OS pre-installed units will come with the partition
required for TPM deployment. NOTE: The TPM key is unique to every TPM deployed server and must
be retained. Misplacing or losing the key could result in data loss.
HP Storage Controllers
SAS Controllers NOTE: Support for SAS hard drives/tape
drive requires selection of a SAS controller. NOTE: Support for hardware RAID requires selection of a SAS controller.
Smart Array P212 Controller
HP Smart Array P212/ZM 1-ports
Int/1-ports Ext PCIe x8 SAS Controller
HP 650 mAh P-Series Battery NOTE: Required to enable BBWC on
the 256MB cache.
462969-B21
HP Non-Hot Plug Internal SAS/SATA
4 Port Cable Kit NOTE: This cable will only be required
when Smart Array Controller is ordered with a BTO configuration.
487734-B21
HP Smart Array Advanced Pack including
1yr 24x7 Technical Support and Updates Single Server License NOTE: This part number can be used
to purchase a single license or to order multiple licenses with a single
activation key. Customers will receive a license entitlement certificate
via e-mail. The license entitlement certificate must be redeemed online
or via fax in order to obtain the license activation key(s). Include one
year of 24x7 HP Software Technical Support Services.
HP SC11Xe Ultra320 Single Channel/
PCIe x4 SCSI Host Bus Adapter NOTE: Supports SCSI Tapes only, no
RAID support. NOTE: HBA is recommended for SCSI tape drive support. NOTE: Please see the following QuickSpecs for Technical Specifications
and additional information: http://h18004.www1.hp.com/products/quickspecs/12566_na/12566_na.html
(SC11Xe HBA)
NOTE: For the
complete range of StorageWorks tape drives, autoloaders, libraries and media
see: http://www.hp.com/go/tape.
For hardware and software compatibility of HP StorageWorks tape backup products
see: http://www.hp.com/go/connect.
HP StorageWorks DAT 320 USB Internal
Tape Drive
AJ825A
HP StorageWorks DAT 320 SAS Internal
Tape Drive NOTE: Connection using HP P212 Smart
Array Controller SAS ( 462828-B21) recommended.
AJ830A
HP StorageWorks Ultrium 448 SAS Internal Drive NOTE: Connection using HP P212
Smart Array Controller SAS ( 462828-B21) recommended.
DW085A
HP StorageWorks Ultrium 920 SAS
Internal Tape Drive NOTE: Connection using HP P212 Smart
Array Controller SAS ( 462828-B21) recommended.
EH847A
HP StorageWorks 1/8 G2 Ultrium
920 SAS Autoloader NOTE: Requires HP 1U Tape Autoloader
Rack-Mount Kit (AH166A) for rack installation. Connection using HP P212
Smart Array Controller SAS ( 462828-B21) recommended.
AH558A
HP StorageWorks MSL2024 Ultrium
920 SAS Tape Library NOTE: Connection using HP P212 Smart
Array Controller SAS ( 462828-B21) recommended.
HP StorageWorks D2D Backup Systems
with Backup Data Deduplication
NOTE: These are
network connected appliances with connectivity using the iSCSI protocol.
If the server requires a hardware iSCSI initiator, the QLogic QLA4050 Host
Bus Adapter is recommended.
HP StorageWorks D2D2502i Backup
System NOTE: 1.5TB of usable network disk
backup capacity. Network connected appliance with connectivity using the
iSCSI protocol. If the server requires a hardware iSCSI initiator, the QLogic
QLA4050 Host Bus Adapter is recommended.
EJ001B
HP StorageWorks D2D2504i Backup
System NOTE: 3.0TB of usable network disk
backup capacity. Network connected appliance with connectivity using the
iSCSI protocol. If the server requires a hardware iSCSI initiator, the QLogic
QLA4050 Host Bus Adapter is recommended.
EJ002B
USB Removable Media RDX Disk Backup
Systems
HP StorageWorks RDX320 Internal
Removable Disk Backup System NOTE: 320GB of disk capacity per
data cartridge.
AJ767A
HP StorageWorks RDX500 Internal
Removable Disk Backup System NOTE: 500GB of disk capacity per
data cartridge.
AJ934A
HP Uninterruptible
Power Systems
HP Tower UPS
HP T750 G2 UPS Models
HP T750 G2 750VA Tower Uninterruptible
Power System
AF446A
HP T1000 G3 UPS Models
HP T1000 G3 1000VA Tower Uninterruptible
Power System
AF448A
NOTE: For additional
information regarding HP Uninterruptable Power Systems, please see the following
URL: www.hp.com/go/rackandpower
(Worldwide) NOTE: For additional information on sizing your server, please reference:
http://www.upssizer.com
NOTE: Please see
the UPS and PDU cable matrix's on the HP Power Protection and Management
page. Under Power Cords, click on the "HP Power Cord Matrix" link.
That link will list cable descriptions, requirements, and specifications
for UPS and PDU units. Please see the following link: www.hp.com/products/powercords.
NOTE: The increasing power of new high-performance processor technology
requires increased cooling efficiency for rack-mounted servers. The 10000
G2 Series Racks provide enhanced airflow for maximum cooling, allowing
these racks to be fully loaded with servers using the latest processors.
CAUTION: If a third-party rack is used, observe the following additional
requirements to ensure adequate airflow and to prevent damage to the equipment:
Front and rear doors: If your 42U server rack
includes closing front and rear doors, you must allow 830 square inches
(5,350 sq cm) of hole evenly distributed from top to bottom to permit
adequate airflow (equivalent to the required 64 percent open area for
ventilation).
Side: The clearance between the installed rack component and the side
panels of the rack must be a minimum of 2.75 inches (7 cm).
CAUTION: Always use blanking panels to fill all remaining empty
front panel U-spaces in the rack. This arrangement ensures proper airflow.
Using a rack without blanking panels results in improper cooling that
can lead to thermal damage.
NOTE: HP ProLiant
DL rack models have fixed rails which provide support for racks with round
mounting holes and tool-free support for racks with square mounting holes
(including Compaq/HP 7000, 9000, 10000 and HP series), with an adjustment
range of 26" - 36". NOTE: Support for all 2 and 4 post Telco racks and threaded hole
racks requires an additional option kit from Rack Solutions. The Rack Solutions
brackets can be purchased at: www.hp.com/go/rackandpower.
HP Rack Options
HP KVM Switch Options
Server console switch 0x2x8
AF616A
Server console switch 0x2x16
AF617A
0x2x16 KVM Server Console G2 Switch
with Virtual Media and CAC
AF618A
0x2x32 KVM Server Console G2 Switch
with Virtual Media and CAC
AF619A
1x1Ex8 KVM IP Console Switch G2
with Virtual Media and CAC
AF620A
2x1Ex16 KVM IP Console Switch
G2 with Virtual Media and CAC
AF621A
4x1Ex32 KVM IP Console Switch
G2 with Virtual Media and CAC
AF622A
NOTE: For additional
information regarding KVM Switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm.
NOTE: For the
installation of Windows and other OS's, a floppy drive or the HP USB Floppy
Drive Key may be required to complete driver installation. A standard USB
drive key may not work to complete driver installation.
HP Care Pack Services
Hardware Services Next Business
Day On-Site Service
9-Hour x 5-Day Coverage, 3 Years,
Electronic
U4433E
Hardware Services - 4-Hour On-site
Service
13-Hour x 5-Day Coverage, 3 Years,
Electronic
U4434E
24-Hour x 7-Day Coverage, 3 Years,
Electronic
U4435E
Hardware Services 6-Hour Call
to Repair On-Site Service
6-Hour Call to Repair, On-Site
Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
NOTE: Memory configurations
listed do not apply to "Factory Integrated Models".
Standard Memory
SATA Models:
2GB or 4 GB of PC3-10600E DDR3 UDIMM running up to 1333MHz with memory kits
installed.
Standard Memory with Optional
Memory
Up to 8GB of memory is available
with the installation of standard and optional memory, 4x 2 GB PC3-10600E
un-buffered ECC DDR3 SDRAM DIMM Memory kits.
NOTE: The below
chart does not represent all possible memory configurations. NOTE: For best performance, it is recommended that customer installs
memory in identical pairs (Slots 1C and 3D are interleaving pair. Slots
2A and 4B are interleaving pair).
NOTE: All DDR3
memory option kits consist of one DIMM per kit. For detailed memory configuration
rules and guidelines, please use the Online DDR3 Memory Configuration Tool:
www.hp.com/go/ddr3memory-configurator.
ML110 G6 Hard Drives (SATA Models
only) NOTE: The components of a storage
subsystem (e.g. the drive, the HBA/controller, and firmware) should operate
at the same data transfer rate or the system bandwidth will be negotiated
down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
SATA Non-Hot Plug
LFF (3.5-inch) Midline (MDL) Drives
Quantity
Supported
Position
Supported
Controller
2TB 3G 7.2K
1TB 3G 7.2K
500GB 3G 7.2K
Up to 4
3,4,5,6
Smart Array B110i SATA RAID Controller
(RAID 0/1/10) NOTE: Hardware RAID support requires
purchase of HP Smart Array P212 Controller.
SATA Non-Hot Plug
LFF (3.5-inch) Entry (ETY) Drives
Quantity
Supported
Position
Supported
Controller
250GB 3G 7.2K
160GB 3G 7.2K
Up to 4
3,4,5,6
Smart Array B110i SATA RAID Controller
(RAID 0/1/10) NOTE: Hardware RAID requires purchase
of HP Smart Array P212 Controller.
ML110 G6 Hard Drives (SAS Models
only)
SAS Non-Hot Plug LFF
(3.5-inch) Enterprise (ENT) Drives NOTE: SAS non-hot plug drives require
HP SAS/Smart Array Controller.
Quantity
Supported
Position
Supported
Controller
600GB 6G 15K DP
450GB 6G 15K DP
300GB 6G 15K DP
Up to 4
3,4,5,6
Smart Array P212 Controller NOTE: Transfer rates of drives are
dependent on the maximum transfer rate supported by the Controller. Refer
to the Controller technical specifications for details.
Maximum Storage
Capacity - SATA/SAS Models
Internal
SATA
8.0TB (4 x 2TB)
SAS
2.4TB (4 x 600GB)
Tape and Disk-Based
Backup
NOTE:
For the complete range of StorageWorks tape drives, autoloaders, libraries
and media, including the internal fitting models, see: http://www.hp.com/go/tape.
For the complete range of StorageWorks D2D Backup Systems see: http://www.hp.com/go/d2d.
For the complete range of StorageWorks RDX drives and media see: http://www.hp.com/go/rdx.
For hardware and software compatibility of HP StorageWorks disk and tape
backup products see: http://www.hp.com/go/connect.
Position
Recommended Controller
Part Number
HP StorageWorks SCSI Tape Drives
LTO-1 Ultrium 232
LTO-2 Ultrium 448
LTO-3 Ultrium 920
LTO-3 Ultrium 960
LTO4 Ultrium 1760
LTO-4 Ultrium 1840
DAT 40
DAT 72
DAT 160
Internal or External
HP SC11Xe Ultra320 Single Channel/ PCIe x4 SCSI Host Bus
Adapter
HP StorageWorks Fibre Channel
Tape Libraries
MSL2024
MSL4048
MSL8096
MSL6000
External
Please consult the
EBS connectivity matrix at: http://www.hp.com/go/ebs
for connectivity information and the supported Fibre Channel HBAs shown
in this QuickSpecs.
HP StorageWorks USB RDX Removable
Disk Backup System
RDX160
RDX320
RDX500
RDX750
Internal or External
USB 2.0 port
N/A
HP StorageWorks D2D Backup
Systems, iSCSI
D2D2500i
D2D4000i
External
Embedded Network
Controller. If the server requires a hardware iSCSI initiator, the QLogic
QLA4050 Host Bus Adapter is recommended.
HP StorageWorks D2D Backup
Systems, Fibre Channel
D2D4000fc
System Leakage with all power supplies loaded
(mA)
3.5mA@110V
3.5mA@220V
System Inrush Current with all power supplies
loaded (A)
<150A@240Vac
Power cord requirements
Nema 5-15P to IEC320-C13
IEC320-C13 to IEC320-C14
**Power shown is for
a fully configured system consisting of (1) CPU, (4) double-sided DIMMs,
(4) HDDs, (1) DVD-ROM, (4) PCI cards, and (1) power supply.
Power Cords (13 Cord Sets)
Power Cord Part Number
Country
121565-001
NOTE:
To review typical system power ratings use the Active Answers HP Power Advisor
which is available via the online tool located at URL: http://www.hp.com/go/hppoweradvisor
To drill down to calculators:
- Click on: "ProLiant Servers"
- Click on the Server of interest. Example: ML110 G6
- Click on: "Power Calculator" link. (You may need to scroll down
to see it)
Maximum
(all hard drives, power supplies, and processors installed)
30.53 lb (13.85 kg)
Minimum
(one hard drive, power supply, and processor installed)
25.13 lb (11.4 kg)
Input Requirements
(per power supply)
Rated Line Voltage
90 to 132 VAC,
180 to 264 VAC
Rated Input Current
5 A (at 100 VAC),
2.5 A (at 200 VAC)
Rated Input Frequency
47 to 63 Hz
Rated Input Power
400 W (at 100 VAC),
400 W (at 200 VAC)
Power Specifications
To review typical
power ratings use the Power Advisor which is available via the online tool
located at URL: http://www.hp.com/go/hppoweradvisor
Power Supply Output
(per power supply)
Rated Steady-State Power
300 W (at 100 VAC),
300 W (at 200 VAC)
Maximum Peak Power
300 W (at 100 VAC),
300 W (at 200 VAC)
System Inlet Temperature
Operating
10° to 35°C (50° to
95°F) at sea level with an altitude derating of 1.0°C per every
304.8 m (1.8°F per every 1000 ft) above sea level to a maximum of 3048
m (10,000 ft), no direct sustained sunlight. Maximum rate of change is 10°C/hr
(18°F/hr). The upper limit may be limited by the type and number of
options installed.
System may shut down if operating with a fan fault or above 42°C °(107.6°F).
Non-operating
-35° to 65°C (-31°
to 149°F). Maximum rate of change is 20°C/hr (36°F/hr).
Relative Humidity
(non-condensing)
Operating
10% to 90% relative humidity (Rh),
28°C (82.4°F) maximum wet bulb temperature, non-condensing.
Non-operating
10% to 95% relative humidity (Rh),
38.7°C (101.7°F) maximum wet bulb temperature, non-condensing.
Altitude
Operating
3048 m (10,000 ft). This value
may be limited by the type and number of options installed. Maximum allowable
altitude change rate is 609 m/min (2000 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 609 m/min (2000 ft/min).
Acoustic Noise
Listed are the declared
A-Weighted sound power levels (LWAd) and declared average bystander position
A-Weighted sound pressure levels (LpAm) when the product is operating in
a 23°C ambient environment. Noise emissions were measured in accordance
with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
Idle
L WAd
4.32 Bels
L
pAm
24.9 dBA
Operating
L WAd
4.41 Bels
L pAm
25 dBA
NOTE:
The listed sound levels above apply to standard SATA configurations. Additional
options may result in increased sound levels.
Emissions Classification
(EMC)
FCC Rating
Class B
Normative Standards
CISPR 22; EN55022; EN55024; FCC
CFR 47, Pt 15; ICES-003; CNS13438; GB9254; EN 61000-3-2; EN 61000-3-3; EN
60950-1; IEC 60950-1
NOTE:
Product conformance to cited product specifications is based on sample (type)
testing, evaluation, or assessment. This product or family of products is
eligible to bear the appropriate compliance logos and statements.
HP 160GB 3G SATA 7.2K rpm LFF
(3.5-inch) Non-hot Plug Entry 1yr Warranty Hard Drive
Operating Temperature
(system inlet air temperature)
50°
to 95° F (10° to 35° C)
HP 250GB 3G SATA 7.2K rpm LFF
(3.5-inch) Non-hot Plug Entry 1yr Warranty Hard Drive
571232-B21
Capacity
250,059MB
Height
Maximum drive dimension
1.028 in. (26.1
mm)
Width
4.00 in (101.6
mm)
Depth
Maximum drive dimension
5.787 in (147.0
mm)
Interface
Serial ATA
Transfer Rate
(Maximum)
3Gb/s
Native Command Queuing
Supported
Seek Time
(typical reads, including settling)
Single Track
2.0 ms
Average
11 ms
Full-Stroke
21.0 ms
Rotational Speed
7,200 rpm
Physical Configuration
Bytes/Sector
512
Logical Blocks
488,397,168
Operating Temperature
(system inlet air temperature)
50°
to 95° F (10° to 35° C)
HP Half-Height 16X Max
SATA DVD-ROM Optical Drive
Disk
Applicable Disk
CD-ROM, CD-XA, CD-DA
(Mode 1, Mode 2, Form 1 and 2)
Photo CD (Single and Multi-session)
Mixed Mode (Audio and Data combined)
CD-R, CD-RW, DVD-ROM, DVD+R, DVD+RW
Capacity
4.7 GB (DVD-5)
8.54 GB (DVD-9)
Block Size
DVD Media
2,048 bytes
Interface
SATA
3Gb/s
Access Times (typical)
Random
<140 ms
Full-Stroke
<250 ms
Data Transfer Rate
Sustained
8100 to 21600 KB/s (6X to 16X)
Cache Buffer
128 KB
Start-up Time (typical)
< 7 seconds
Stop Time
< 4 seconds
Laser Parameters
Type
Semiconductor Laser GaA1As
Wave Length
780 ± 25 nm
Operating Conditions
Temperature
41° to 122° F (5° to
50° C)
Humidity
10% to 90%
Dimensions
(HxWxD, maximum)
1.7 x 5.85 x 8.11 in (42.9 x 150
x 195 mm)
Weight
2.64 lb (1.2 kg)
Embedded NC107i PCIe Gigabit Server Adapter (Embedded)
Network Interface
Integrated 10/100/1000BASE-T
Transceiver
Combines a triple-speed
IEEE 802.3TM - Compliant Media Access Controller (MAC) with a triple-speed
Ethernet transceiver.
Data Transfer Method
Compliant to x1 PCIe
Specification
Controller
BCM5723
Network Transfer Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX (Half and Full-Duplex)
2000Mb/s
Connector
RJ-45 connector
Cable Support
Performs all the physical
layer functions for 10BASE-T, 100BASE-T, and 1000BASE-T Ethernet on standard
Category 5 UTP
Environment-friendly Products and Approach
End-of-life Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go
to: http://www.hp.com/go/green.
To recycle your product, please go to: http://www.hp.com/go/green
or contact your nearest HP sales office. Products returned to HP will
be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment
information for each product type for use by treatment facilities. This
information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green.
These instructions may be used by recyclers and other WEEE treatment facilities
as well as HP OEM customers who integrate and re-sell HP equipment.
DL QuickSpecs
US QuickSpecs 
500672-B21
