512 MB Standard / 8 GB Maximum of PC2-5300 DDR2
667 MHz ECC unbuffered Memory
Storage Controller:
4 Port SATA controller with Embedded RAID on
Motherboard (RAID 0,1,5)
Internal Drive Support:
4 HDD Support:
2TB SATA max storage (utilizing 500GB CTO
HDD)
1.2TB SAS max storage (4 x 300GB)
Network Controller:
Embedded NC320i PCI Express Gigabit Server Adapter
Expansion Slots:
Two 32-bit/33MHz PCI at 3.3V slot
Two PCI-Express slots (x8 and x16).
USB Ports:
Eight total USB ports (2 internal, 2 front,
4 rear)
Form Factor:
Micro ATX tower
Management:
Standard IPMI reporting
Lights Out 100c Remote Management Card (Optional)
Warranty: This
product is covered by a global limited warranty and supported by
HP Services and a worldwide network of HP Authorized Channel Partners.
Hardware diagnostic support and repair is available for one year
from date of purchase. Support for software and initial setup is
available for 90 days from date of purchase. Additional support
may be covered under the warranty or available for an additional
fee. Enhancements to warranty services are available through HP
Care Pack services or customized service agreements.. Certain restrictions
and exclusions apply. SATA hard drives have a one year warranty.
(3-1-1 warranty offered in AP only).
Lights Out LO100c is a
Remote Management Card (RMC) for HP ProLiant 100 series servers that do not have
embedded LO100i. The LO100c has all the features of the LO100i Advanced license
and allows customers, or their service providers, to remotely manage ProLiant
servers over a LAN or the Internet from anywhere, anytime regardless whether the
server is located in the same building, across town, or around the globe.
With LO100c, users can acquire complete remote control with Virtual KVM (graphical
hardware-based, remote console). Users can also access the server's serial console,
control system power, update system firmware and software, as well as monitor
system environmental conditions. The LO100c remote management card can be accessed
from a web browser or command line interface. This virtual "at-the-server"
functionality means administrators stay in control of remote HP ProLiant 100 series
servers.
The HP Lights-Out100c consists of a management processor and
firmware that provides cost-effective, entry-level lights-out functionality, basic
system board management functions, and diagnostics.
Subscriber's
Choice Driver and Support Alerts/Notifications is a web-based email subscription
service that provides software and driver change notifications for ProLiant products.
Sign up at: http://www.hp.com/go/subscriberschoice
and customize your profile to receive various new alerts as they become available,
on a weekly or monthly basis.
ROMPaq
software and latest drivers
The
latest software, drivers, and firmware fully optimized and tested for your ProLiant
server and options, available through ProLiant Support Packs or downloaded from
software and drivers download pages website at: http://www.hp.com/go/support.
Industry Standard
Compliance
ACPI V2.0 Compliant
PCI 2.3 Compliant
PXE Support
WOL Support
IPMI 2.0 compliance
Manageability
Embedded IPMI standard reporting
Optional HP ProLiant Lights-Out 100c Remote Management Card
Security
Power-on password
Setup password
Server Power Cords
12' country specific, lowline
NEMA power cord.
NOTE:
Rack models ship standard with a 12' IEC cable. Most redundant power
supply options ship with a 6' country specific power cord. Localized cables
included with geographic specific models in other world regions.
Power Supply
370 Watts
System
Fans
1 Non-redundant
system fan shipped standard
1
Non-redundant CPU heatsink fan shipped standard
OS
Support
Microsoft Windows Server
2003: Standard & Enterprise Edition (32 and 64 bit) Microsoft Windows
Small Business Server 2003 Microsoft Windows 2003 Server, Web Edition Microsoft
Windows Server 2008 Novell NetWare 6.5 SBS (only after SP6 release) RedHat
Enterprise Linux SUSE Linux Enterprise Server
HP Factory Express offers configuration, customization, integration and deployment
services for HP servers and/or storage products. Customers can choose how their
factory solutions are built, tested, integrated, shipped and deployed.
Factory
Express offers service packages for simple configuration, racking, installation,
complex configuration and design services as well as individual factory services,
such as image loading, asset tagging and custom packaging HP products supported
through Factory Express include a wide array of servers and storage: HP Integrity,
HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000 servers, as well
as, the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network
switches.
For
more information on Factory Express services for your specific server model please
contact your sales representative or go to: http://www.hp.com/go/factory-express.
HP Enterprise Configurator
The HP eCo-Enterprise Configurator now provides factory default racking
for our HP hardware portfolio. This approach is aligned with our strategic
direction to meet the needs and expectations of our valued customers.
If you require "custom" rack configuration, please contact HP's
Customer Business Center or an Authorized Partner for assistance.
Service and Support
HP Care Pack Services provide total care and support expertise with committed
response designed to meet your IT and business needs.
HP Care Pack services include coverage for the HP branded hardware options
qualified for the server that are purchased at the same time or afterward
and internal to the enclosure. It also includes the 22" and smaller
external monitors and tower UPS options up to 3kVA. These items will be
covered at the same service level and for the same coverage period as
the server. Coverage of UPS Battery is not included and standard warranty
terms & conditions apply. For servers or storage systems installed
within a rack, service also covers all HP qualified rack options installed
within the same rack.
To fully capitalize on your HP ProLiant servers' capabilities requires
a service partner who thoroughly understands your server technology and
systems environment. HP Services, an industry leader in provision of multi
vender support solutions provides a range of support services designed
to meet the varying needs of business. Whether an SMB or large global
corporation HP has a ProLiant server support offer to help you speedily
deploy and maximize system uptime.
Recommended Service - Simplify ProLiant solution implementation,
maintenance and management.
Support Service -3 Year, 9x5 Next Business Day coverage, excluding
HP holidays only
Deployment Service - Hardware Installation only
Enhanced Service - Optimize service level to increase IT performance
and availability
Support Service - 3 Year 13x5 Same Business Day, 4-Hour response
coverage
Deployment Service - Installation and Start-up only
Installation & Start-Up of a ProLiant server and Microsoft or Linux
O/S per the Customer Description and/or Data Sheet. To be delivered on
a scheduled basis 8am-5pm, M-F, excl. HP holidays.
NOTE: For the Standard Features shipped in the "Factory Integrated
Models", please see the "Configuration Information - Factory
Integrated Models" section.
SATA Models
ML115 Opteron
1210 NHP-SATA (1P)
437288-xx1
ML115 Opteron 1214 NHP-SATA (1P)
437289-xx1
Processor(s) One of the following depending on Model
NOTE:
This section lists some of the steps required to configure a Factory
Integrated Model. To ensure only valid configurations are ordered, HP recommends
the use of an HP approved configurator. Contact your local sales representative
for information on CTO product offerings and requirements. NOTE: HP does not allow factory integration of options into standard
models listed above.
Configure-to-order servers must start with a CTO Chassis. NOTE: This product offering does not support HP Factory Express Server
Configuration Level 1. NOTE: FIO indicates that this option is a Factory Installable Option.
Step 1:
Base Configuration
Models
HP ProLiant ML115 NHP CTO Chassis
(North America)
439138-B21
Factory Integrated Models ship
with:
Embedded NC320i PCI Express Gigabit
Server Adapter
Keyboard and Mouse
370 Watts, PFC (Power Factor Correcting)
Tower Form Factor (4U)
NOTE: HP SATA
Drive Models are limited to <2TB support.
NOTE: For the
installation of Windows and other OS's, a floppy drive (DC361B) may be required
to complete driver installation. A USB drive key may not work to complete
driver installation.
Step 3: Choose Additional Options
for Factory Integration NOTE: For additional options, please
refer to the "Options" section below. NOTE: Some options may not be factory integratable. Please contact
your local sales representative for additional information.
Operating Systems
Pre-install Microsoft Windows
2003 SBS Standard Edition
NOTE: For the
installation of Windows and other OS's, a floppy drive may be required to
complete driver installation. A USB drive key may not work to complete driver
installation.
ML115 G1 Hard Drives
Serial – ATA (SATA) –
Non-Hot Plug (SATA Models Only)
NOTE: When purchasing
systems with the 500GB Non-Hot Plug SATA drives, please reference the Configuration
Information Section of this QuickSpecs to order via Configuration to Order.
HP Non-Hot Plug SATA Cable NOTE: The purchase of a SATA Hard Disk Drive requires the purchase
of HP SATA Cable option kit (P/N 442901-B21).
442901-B21
Serial Attached SCSI (SAS)
Non-Hot Plug (SAS Models Only)
NOTE: The purchase
of SAS hard drives requires the purchase of part number 430479-B21, the
HP Internal SAS/SATA 4-Port Cable. This cable is standard in the SAS BTO
model.
HP 8 Internal Port SAS HBA with
RAID NOTE: PCI-X Interface (PCI 32bit/33MHz
compatible) NOTE: Slot 2 only supports standard PCI 32 bit add-on card due to
proximity to Heat Synk.
64-Bit/133-MHz Single Channel
Ultra320 SCSI HBA G2 NOTE: PCI-X Interface (PCI 32bit/33MHz
compatible) NOTE: Slot 2 only supports standard PCI 32 bit add-on card due to
proximity to Heat Synk
NOTE: For additional
information regarding KVM Switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm.
NOTE: Memory
configurations listed do not apply to "Factory Integrated Models".
Standard Memory
512 MB of PC2-5300 DDR2 SDRAM
running at 512 MB with ECC capabilities Memory installed (1 x 512 MB SDRAM
DIMM).
Standard Memory Plus Optional
Memory
Up to 5120 MB memory is available
with the optional installation of PC2-5300 un-buffered ECC DDR2 SDRAM DIMM
Memory kits.
Standard Memory Replaced
with Optional Memory
Up to 8192 MB of memory is available
with the removal of the standard 512 MB of memory and the optional installation
of PC2-5300 un-buffered ECC DDR2 SDRAM DIMM Memory kits.
NOTE: The below
chart does not represent all possible memory configurations. NOTE: In memory configurations requiring 2 DIMM and 4 DIMM configurations,
the memory must be paired for optimal performance. This means that DIMMs
in slot 1 and 3 have to be identical, in slot 2 and 4 have to be identical.
(For example, the Optional memory configuration shown below)
3.5-inch
500GB 7.2K SATA
250GB 7.2K SATA
160GB 7.2K, SATA
80GB
7.2K, SATA
Up to 4
3,4,5,6
4 Port SATA controller with Embedded
RAID on Motherboard (0,1,5)
ML115 G1 Hard Drives (SAS Models only)
SAS – Non-Hot Plug
Quantity
Supported
Position
Supported
Controller
3.5-inch
300GB 15K SAS
145GB 15K SAS
72GB 15K, SAS
Up to 4
3,4,5,6
HP 8 Internal Port SAS HBA with
RAID (0,1)
Maximum Storage
Capacity – SATA/SAS Models
Internal
SATA
1TB (4x250GB (BTO)
2TB (4 x 500GB (CTO)
SAS
1.2TB (4x300GB)
Total
SATA
1TB (4x250GB (BTO)
2TB (4 x 500GB (CTO)
SAS
1.2TB (4x300GB)
Tape Drives and D2D
Backup System
NOTE: A
SCSI controller needs to be purchased to operate internal SCSI devices in
the SATA Models. NOTE: For an up-to-date listing of the latest O/S Support details
for each of the Tape Drives listed below, please see the following: http://h18000.www1.hp.com/products/quickspecs/division/10233.html
(Worldwide)
Position
Supported
Controller
Controller/HBA Option Kit Part Number
Internal USB Tape Drives
DAT 40 USB
DAT 72 USB
DAT 160 USB
2
USB 2.0 port
N/A
External USB Tape Drives
DAT 40 USB
DAT 72 USB
DAT 160 USB
System Leakage with all power supplies loaded
(mA)
0.75mA@240V
0.45mA@120V
System Inrush Current with all power supplies
loaded (A)
80A
Power cord requirements
Nema 5-15P to IEC320-C13
IEC320-C13 to IEC320-C14
**Power shown is for
a fully configured system consisting of (1) CPU, (4) double-sided DIMMs,
(4) HDDs, (1) CD-ROM, (1) DVD-ROM, (4) PCI cards, and (1) power supply.
HP 8 Internal Port SAS Host Bus Adapter with RAID (SAS Model only)
Dimensions (excluding bracket)
6.6 x 2.5 x 0.6 in
(16.8 x 6.4 x 1.6 cm)
Disk Drive and Enclosure Protocol
Support
3 Gbps SAS (Serial
Attached SCSI)
1.5 Gbps SATA (Serial Advanced Technology Attachment)
Architecture
64-bit
SAS Connectors
2 internal SFF8484
x4 Wide SAS Connectors
12 Gbps per x4 Wide SAS Port (4 x 3 Gbps)
Data Transfer Method
64-bit wide, PCI-X
133 MHz (1 GB/s maximum bandwidth)
PCI Bus Speed
PCI-X-133 and 3.3
volt PCI compatibility only
PCI
PCI-X and 3.3 volt
PCI compatibility only
Simultaneous Drive Transfer Ports
2 x4 Wide SAS Connectors
Port Transfer Rate
12 Gb/s per x4 Wide
SAS Port (4 x 3 Gb/s)
Software upgradeable Firmware
Yes
Maximum Capacity
576GB (8 x 72GB)
Memory Addressing
64-bit, supporting
servers memory greater than 4 GB
Logical Drives Supported
Up to 2 Logical Volumes
Up to 10 drives total in all RAID volumes
Up to 2 Drives per RAID 1
Up to 8 Drives per RAID 0
RAID Support
RAID 1 (Mirroring)
RAID 0 (Striping)
Upgradeable Firmware
4-MB flashable ROM
Disk Drive and Enclosure Protocol
Support
3 Gbps SAS and 1.5
Gbps SATA
NOTE: Slot 2 only
supports standard PCI 32 bit add-on card due to proximity of the Heat Sink.
Embedded NC320i PCIe Gigabit Server Adapter
Network Interface
10Base-T/100Base-TX/1000Base-TX
Compatibility
IEEE 802.3 10Base-T
IEEE 802.3ab 1000Base-T
IEEE 802.3u 100Base-TX
Data Transfer Method
Single lane (x1),
100MHz PCI Express Reference Clock
Network Transfer
Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX (Half and Full-Duplex)
2000Mb/s
Connector
RJ-45 connector
Cable Support
10Base-T
Categories 3, 4 or 5 UTP; up to
328 ft (100 m)
10/100/1000Base-TX
Category 5 UTP; up to 328 ft (100
m)
Environment-friendly Products
and Approach
End-of-life Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go
to http://www.hp.com/go/green.
To recycle your product, please go to: http://www.hp.com/go/green
or contact your nearest HP sales office. Products returned to HP will
be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide
treatment information for each product type for use by treatment facilities.
This information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green.
These instructions may be used by recyclers and other WEEE treatment facilities
as well as HP OEM customers who integrate and re-sell HP equipment.